 |
|
 |
ATV
Silencer ATV Silencer / 4 Wheeler Mufflers / 4 Wheeler Exhaust Systems
---- IMPORTANT NOTE ----
If riding your ATV in altitudes of 6000 ft. or above, please make a note on your order in the Special Instructions section of the order form, as these particular units must be vented to allow airflow. 
ATV ExhaustCategory - ATV Exhaust SilencerSupported ATV Models:Models below marked with a * will use the adapter provided in the kit at no extra charge. These adapters will require welding to the factory muffler. This will create an attachment point for the silencer to pressure fit on and off of. ONLY the adapter is permanent. Some models do not need an adapter, being the factory muffler has enough flange to attach to. The models listed below have an optional bolt on adapter that will use the same bolt pattern, so no new holes will be needed. Optional bolt on adapter available for these models listed below: $22.95 HONDA
If you do not see your particular model listed under ATV Exhaust -, please call us at 1-877-327-5270 toll free and we can always check to see if we have anything for your ATV. The ATV Exhaust Silencer - attaches to the stock -. If there is not enough lip or tail pipe to attach to, then an adapter is required to complete the installation. Some adapters need to be welded to the stock pipe to create an attachment point. Other models have an optional bolt on adapter that is available for an extra $21.95. Also, there are some models that do not require any type of adapter. Some particular ATV Exhaust Silencer Adapters - need to be welded to the tail pipe that drops out the bottom of stock -. This gives the silencer something to attach to. The silencer is not permanent, just the 1 1/2" adapter. Note: The ATV Exhaust Silencer - is not a permanent device, you can choose to leave it on or take it off by 2 bolt hangers. The ATV - Exhaust silencer - is easy to install. Depending on whether or not an adapter is needed, here are is the general procedure. The ATV - Exhaust silencer is slid over the attached adapter, if needed. Drill 2 small holes in the cross member. Then place the silencer onto the adapter and insert bolts through flat hanger brackets and through cross member. Follow with rubber grommets, washer, and nut. Tighten for secure hold. |
| The Silent ATV Exhaust fits most any ATV with a four stroke engine to quiet the stock noise by 60-80%, without sacrificing any engine performance. Some ATV Exhaust systems require welding to the stock exhaust in order for the muffler to be attached.
Our ATV Exhaust systems have easy installation and are not permanent; they can be removed as desired. The adapter for the ATV Exhaust, if needed, will be the only permanent attachment made to the stock muffler. The Benz Silent Rider ATV Exhaust is ideal for hunters who want to be quiet in the woods. The silent ATV Exhaust system supports many models made by the following manufacturers: Yamaha, Kawasaki, Honda, Polaris, Artic Cat, & Suzuki If you do not see your particular model listed under ATV Exhaust, please call us and we can always check to see if we have anything for your ATV. The ATV Exhaust Silencer attaches to the stock muffler. If there is not enough lip or tail pipe to attach to, then an adapter is required to complete the installation. Some adapters need to be welded to the stock pipe to create an attachment point. Other models have an optional bolt on adapter that is available for an extra $21.95. Also, there are some models that do not require any type of adapter. Some particular ATV Exhaust Adapters need to be welded to the tail pipe that drops out the bottom of stock muffler. This gives the silencer something to attach to. The silencer is not permanent, just the 1 1/2" adapter. Note: The ATV Exhaust Silencer is not a permanent device, you can choose to leave it on or take it off by 2 bolt hangers. The ATV Exhaust silencer is easy to install. Depending on whether or not an adapter is needed, here are is the general procedure. The ATV Exhaust silencer is slid over the attached adapter, if needed. Drill 2 small holes in the cross member. Then place the silencer onto the adapter and insert bolts through flat hanger brackets and through cross member. Follow with rubber grommets, washer, and nut. Tighten for secure hold. |
 |
